Committee

Committee:

CTN 53/SC 6 - Specifications for commodities and test methods

Secretary:

ANAIP - ASOCIACIÓN ESPAÑOLA DE INDUSTRIALES DE PLÁSTICOS

Structure:

GT 1 Biodegradabilidad y productos de origen biológico

International Relations:

ISO/TC 61 Plastics

ISO/TC 138/SC 5/WG 5 Polyolefin pipes

ISO/TC 219 Floor coverings

CEN/TC 249 Plastics

CEN/TC 411 Bio-based products

* Some activities of this TC correspond to other AEN/CTN.

Standards developed by the committee: CTN 53/SC 6: 966

UNE-EN ISO 11357-4:2021

Status: VIGENTE / 2021-12-15

Plastics - Differential scanning calorimetry (DSC) - Part 4: Determination of specific heat capacity (ISO 11357-4:2021)

UNE-EN ISO 24024-1:2021

Status: VIGENTE / 2021-12-07

Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system (ISO 24024-1:2021)

UNE-EN ISO 24024-2:2021

Status: VIGENTE / 2021-12-07

Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 2: Preparation of test samples and determination of properties (ISO 24024-2:2021)

UNE-EN ISO 20326:2019/A1:2021

Status: VIGENTE / 2021-12-07

Resilient floor coverings - Specification for floor panels/assembly for loose laying - Amendment 1: Requirements depending on the substrate (ISO 20326:2016/Amd 1:2020)

UNE-EN ISO 19679:2021

Status: VIGENTE / 2021-11-17

Plastics - Determination of aerobic biodegradation of non-floating plastic materials in a seawater/sediment interface - Method by analysis of evolved carbon dioxide (ISO 19679:2020)

UNE-EN ISO 294-3:2021

Status: VIGENTE / 2021-11-10

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2020)

UNE-EN ISO 604:2003

Status: VIGENTE / 2021-11-03

Plastics - Determination of compressive properties (ISO 604:2002)

UNE-EN 16760:2016

Status: VIGENTE / 2021-10-12

Bio-based products - Life Cycle Assessment

UNE-EN 16785-1:2016

Status: VIGENTE / 2021-10-12

Bio-based products - Bio-based content - Part 1: Determination of the bio-based content using the radiocarbon analysis and elemental analysis

UNE-ISO 1268-1:2012

Status: VIGENTE / 2021-10-05

Fibre-reinforced plastics -- Methods of producing test plates -- Part 1: General conditions

UNE-ISO 1268-2:2012

Status: VIGENTE / 2021-10-05

Fibre-reinforced plastics -- Methods of producing test plates -- Part 2: Contact and spray-up moulding

UNE-ISO 1268-5:2012

Status: VIGENTE / 2021-10-05

Fibre-reinforced plastics -- Methods of producing test plates -- Part 5: Filament winding

UNE-ISO 1268-7:2012

Status: VIGENTE / 2021-10-05

Fibre-reinforced plastics. Methods of producing test plates. Part 7: Resin transfer moulding

UNE-EN ISO 844:2021

Status: VIGENTE / 2021-09-29

Rigid cellular plastics - Determination of compression properties (ISO 844:2021)

UNE-EN ISO 11357-8:2021

Status: VIGENTE / 2021-09-29

Plastics - Differential scanning calorimetry (DSC) - Part 8: Determination of thermal conductivity (ISO 11357-8:2021)

UNE-EN ISO 6721-3:2021

Status: VIGENTE / 2021-09-29

Plastics - Determination of dynamic mechanical properties - Part 3: Flexural vibration - Resonance-curve method (ISO 6721-3:2021)

UNE-EN ISO 10350-2:2021

Status: VIGENTE / 2021-09-29

Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2020)

UNE-EN 16795:2016

Status: VIGENTE / 2021-09-06

Plastics - Method for estimating heat build up of flat surfaces by simulated solar radiation

UNE-EN 438-1:2016

Status: VIGENTE / 2021-09-03

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 1: Introduction and general information

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 3: Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates

Back to results New Search

AENORmás

Design your own personalised collection of standards. Keep your standards updated.