Clear filters Apply
Results for:
Number of results 998
UNE-EN 18027:2025 UNE
Status: Current/ 2025-11-19
Bio-based products - Life cycle assessment - Additional requirements and guidelines for comparing the life cycles of bio-based products with their fossil-based equivalents
UNE-EN ISO 10350-1:2025 UNE
Status: Vigente/ 2025-11-05
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2025)
UNE-EN ISO 1628-1:2025 UNE
Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 1: General principles (ISO 1628-1:2024)
UNE-EN ISO 3451-5:2025 UNE
Plastics - Determination of ash - Part 5: Poly(vinyl chloride) (ISO 3451-5:2025)
UNE-ISO 182-1:2025 UNE
Status: Current/ 2025-09-17
Plastics. Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures. Part 1. Congo red method.
UNE-EN ISO 19069-2:2025 UNE
Status: Current/ 2025-09-10
Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19069-2:2024)
UNE-EN 12814-8:2025 UNE
Status: Vigente/ 2025-07-02
Testing of welded joints of thermoplastics semi-finished products - Part 8: Requirements
UNE-EN ISO 17855-2:2025 UNE
Status: Vigente/ 2025-06-18
Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 17855-2:2024)
UNE-EN ISO 16906:2025 UNE
Status: Vigente/ 2025-05-14
Resilient floor coverings - Determination of seam strength (ISO 16906:2015)
UNE-EN ISO 4892-3:2025 UNE
Status: Vigente/ 2025-04-23
Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2024)
UNE-EN ISO 899-2:2025 UNE
Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2024)
UNE-EN ISO 4892-1:2025 UNE
Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance and requirements (ISO 4892-1:2024)
UNE-EN ISO 9773:2025 UNE
Status: Vigente/ 2025-03-26
Plastics - Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source (ISO 9773:2024)
UNE-EN ISO 24342:2025 UNE
Status: Current/ 2025-01-22
Resilient and textile floor-covering - Determination of side length, edge straightness and squareness of tiles and planks (ISO 24342:2024)
UNE-EN ISO 3451-4:2024 UNE
Status: Vigente/ 2024-11-06
Plastics - Determination of ash - Part 4: Polyamides (ISO 3451-4:2024)
UNE-EN ISO 22007-1:2024 UNE
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2024)
UNE-EN ISO 182-3:2024 UNE
Plastics - Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures - Part 3: Conductometric method (ISO 182-3:2023)
UNE-EN 12814-7:2024 UNE
Testing of welded joints of thermoplastics semi-finished products - Part 7: Tensile test with waisted test specimens
UNE-EN ISO 20753:2024 UNE
Plastics - Test specimens (ISO 20753:2023)
UNE-EN ISO 61:2024 UNE
Status: Vigente/ 2024-10-30
Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:2023)
UNE-EN ISO 60:2024 UNE
Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:2023)
UNE 53036:2024 UNE
Status: Vigente/ 2024-09-18
Plastics. Determination of specular gloss of plastic materials
UNE-EN ISO 22007-4:2024 UNE
Status: Vigente/ 2024-07-17
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 4: Light flash method (ISO 22007-4:2024)
UNE-EN ISO 8256:2024 UNE
Status: Current/2024-06-05
Plastics - Determination of tensile-impact strength (ISO 8256:2023)
UNE-EN ISO 4608:2024 UNE
Plastics - Homopolymer and copolymer resins of vinyl chloride for general use - Determination of plasticizer absorption at room temperature (ISO 4608:2023)
UNE-EN ISO 24187:2024 UNE
Status: Current/2024-05-29
Principles for the analysis of microplastics present in the environment (ISO 24187:2023)
UNE-EN ISO 20200:2024 UNE
Status: Vigente/ 2024-04-30
Plastics - Determination of the degree of disintegration of plastic materials under composting conditions in a laboratory-scale test (ISO 20200:2023)
UNE-EN ISO 1172:2024 UNE
Status: Current/2024-04-24
Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content using calcination methods (ISO 1172:2023)
UNE-EN ISO 3671:2024 UNE
Plastics - Aminoplastic moulding materials - Determination of volatile matter (ISO 3671:2023)
UNE-EN ISO 6186:2024 UNE
Status: Vigente/ 2024-03-27
Plastics - Determination of pourability (ISO 6186:2023)
UNE-EN ISO 6603-2:2024 UNE
Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented impact testing (ISO 6603-2:2023)
UNE-EN ISO 13927:2024 UNE
Plastics - Simple heat release test using a conical radiant heater and a thermopile detector (ISO 13927:2023)
UNE-EN ISO 180:2024 UNE
Status: Vigente/ 2024-02-21
Plastics - Determination of Izod impact strength (ISO 180:2023)
UNE-EN ISO 179-1:2024 UNE
Status: Vigente/ 2024-03-20
Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2023)
UNE-EN ISO 527-4:2024 UNE
Status: Vigente/ 2024-01-24
Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:2023)
UNE-EN ISO 11357-1:2023 UNE
Status: Vigente/ 2023-12-27
Plastics - Differential scanning calorimetry (DSC) - Part 1: General principles (ISO 11357-1:2023)
UNE-EN ISO 293:2023 UNE
Status: Vigente/ 2023-11-22
Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2023)
UNE-EN ISO 1675:2023 UNE
Status: Vigente/ 2023-10-31
Plastics - Liquid resins - Determination of density by the pycnometer method (ISO 1675:2022)
UNE-EN ISO 11337:2023 UNE
Plastics - Polyamides - Determination of e-caprolactam and w-laurolactam by gas chromatography (ISO 11337:2023)
UNE-EN ISO 6401:2023 UNE
Status: Vigente/ 2023-06-28
Plastics - Poly(vinyl chloride) - Determination of residual vinyl chloride monomer using gas-chromatographic method (ISO 6401:2022)
UNE-EN ISO 306:2023 UNE
Status: Vigente/ 2023-06-14
Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2022)
UNE-EN 15354:2023 UNE
Plastics - Extruded and/or calendered, non-reinforced film and sheeting made of plasticized poly(vinyl chloride) (PVC-P) - Characterization and designation
UNE-EN ISO 26986:2012/A1:2023 UNE
Status: Vigente/ 2023-05-31
Resilient floor coverings - Expanded (cushioned) poly(vinyl chloride) floor covering - Specification - Amendment 1 (ISO 26986:2010/Amd 1:2022)
UNE-EN ISO 16396-1:2023 UNE
Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 16396-1:2022)
UNE 53218:2023 UNE
Status: Vigente/ 2023-04-19
Plastics. Determination of the resistance to cracking by tensions in active environments of plastic materials of polyethylene and polypropylene.
UNE-EN ISO 11403-2:2023 UNE
Status: Vigente/ 2023-04-05
Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2022)
UNE-EN ISO 1133-1:2023 UNE
Status: Vigente/ 2023-03-08
Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2022)
UNE-EN 17615:2023 UNE
Status: Vigente/ 2023-03-01
Plastics - Environmental Aspects - Vocabulary
UNE-EN ISO 11638:2023 UNE
Resilient floor coverings - Heterogeneous poly(vinyl chloride) flooring on foam - Specification (ISO 11638:2020, including corrected version 2021-09)
UNE-EN ISO 22007-2:2023 UNE
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 2: Transient plane heat source (hot disc) method (ISO 22007-2:2022)
